Clean your sensor (dry)
1. put your camera on a plane.
You have to stick to your camera level when you clean it. This will prevent you from using it as you clean the sensor. Remove the lens exposure sensor so you can start cleaning it.
2. position the digital SLR camera sensor.
Undo the lens and place it on the table. Look at the hole left by the lens until you find a mirror. This mirror is a digital SLR sensor.
3. use a sensor on the bulb blower.
Blow the blower 1 inch (2.5cm) to 2 in (5.1 cm) away from the sensor and sensor start. Move the blower back and forth evenly to clean the sensor.
Bulb blowers can be purchased online or in electronic shops. Do not use the can air blower SLR sensor. Stress is usually strong enough to destroy your sensor.
4. use a sensor to find small dust particles.
The size of the sensor is a magnifying glass, the size of the light. Use scale to see more dust after blowing. Use the bulb blower again where you find more dust.
Sensor sizes can be purchased at most online or camera shops. Turn the camera upside down to drive the SLR sensor out of the dust.
5. after cleaning, take photos and compare the first photo.
Let your second photo as much as possible, and then run it through the same photo modification program. Look for any residual dust if you find any dry cleaning SLR sensors or try to use a clean solution.
2、 Using camera cleaning solution
Buy a sensor cleaning solution.
Do you want to use regular soap or detergent in your camera. With the use of professional digital SLR Sensor Cleaner, can buy online or electronic shops. The digital SLR cleaner leaves a coating, sensor, that can withstand dust and cut back future construction.
2. cleaning solution of dip sensor swab or swab.
Stick to your swab away from touching any target and use it to avoid pollution.
Cleaning Tools were held on the 1st and dipped at the other end.
Read the cleaning direction carefully before you use it. Avoid using cotton balls without a single hold on when cleaning sensor.
3. soak the swabs in the solution for about one minute. A minute is about the time to meet the solution of infiltration into the cleaning tool. When a minute later, stick to the cleaning tool to improve the solution so it can capture any drops. Do not squeeze directly to the digital SLR camera. Use its cleaning tools.
4. carefully drag the swab on the digital SLR sensor.
Tilt swabs are at one corner and then drag from one end of the sensor to the other. Then, drag it back. The swab of the elevator from the sensor in both ways you drag to avoid soiling it.
Use light pressure when you drag swabs on the sensor.
Don't worry about all the dust and your first scrub. You can repeat the process as needed.
5. discard the sensor and use it after scrubbing.
Sensors or swabs cannot be used twice because they will no longer be sterile. If your sensor still looks dirty, use another swab dip solution and try again until it's clean.
3、 Check if the sensor is dirty
1. your ISO is set to the lowest point of normal scale.
Not setting ISO below its scale of expansion may hinder your camera's ability to point all dirty areas of your sensor. If your camera has active ISO settings, change it to manual and adjust the minimum manual ISO command according to your camera.
The lowest ISO size for most digital cameras is 100.
2. turn on the manual focus of your camera.
Capture dust and debris from all sensors to take photos, and you will want the focus of the photo. If you take pictures indoors, set the focus to infinity. If you put it in the wild, pay attention to it.
3. select a medium size and fine pore size.
If your aperture is too large, you may not be able to see any dust. If set very small, however, the details may be so close that you see dust in the air or other targets, rather than your camera sensor.
The F / 22 aperture is usually an ideal level.
4. a blank setting for taking photos.
If your photo is too detailed, you may not be able to distinguish dust from light or vague targets. A white wall, a cloudy sky, or a blank paper is a perfect setting[ 12]
Move the camera slowly, and you will blur the picture further.
5. process photo online viewing location.
Running your photo modified program will help you find dust spots. Fade the photos and add contrast to make the mottled more obvious. The dust of the sensor will be like small, black eye circle will randomly decorate your photos.
If your photo looks more faded than it is found, the lens may need to be cleaned, not your sensor.
Contact Now